My instrument always reads the same
If the instrument is used in the wrong range, it can become oversaturated. This occurs when measurements on mirror-like surfaces (130+GU @60°) are taken using
On a production line, the parts to be measured may be moving or still wet or uncured, with several points to check on each one.
PaintChecker Industrial sensors from OptiSense measure without contact, from 16 mm to 100 mm away depending on the model. They are small and light enough to fix above a conveyor or mount on a robot. One PaintChecker Industrial Controller runs up to eight sensors, records every point at the same time and passes the results to the line PLC and QA systems.
Angle and Tube sensors with a diode laser at 1470 nm and a measuring field of 0.2 or 0.3 mm, for small parts, including their corners and edges. The Angle sensor has folded optics and works 16 mm from the part, in the tightest spaces. The standard-power models are eye-safe, using OptiSense's patented LARES® technology.
Cube sensors with a larger measuring field, 1 mm on Cube-R and 2 mm on Cube-B, for rough, grainy surfaces such as powders and pastes, on metal and non-metallic substrates. Cube-R uses infrared excitation at 980 nm and Cube-B ultraviolet at 365 nm, chosen to suit the coating material. Both are eye-safe. Cube-B now also comes with 75 mm optics.
Higher output in the same housings, for thick layers with a high glass or metal content and for longer distances. Tube-LHP10 works 100 mm from the part with a ±5 mm tolerance, so precise part positioning is often unnecessary. High-power sensors are laser class 3R and are not rated eye-safe.
The Cube-B LED sensor is now also available with 75 mm optics, in the familiar compact cube format. With the 75 mm optics, distance and angle tolerances of ±10 mm and ±20° leave more room for variation in part position, whether the sensor is fixed, held in a fixture or mounted on a robot. Rough and powdery surfaces are measured without contact. The 33 mm optics suit tight integration spaces, edges and smaller radii. Both use UV excitation at 365 nm and run on the LED-B version of the controller.
| 33 mm optics | 75 mm optics | |
|---|---|---|
| Working distance | 33 mm | 75 mm |
| Distance tolerance | ±3 mm | ±10 mm |
| Angle tolerance | ±15° | ±20° |
| Measurement spot diameter | 2 mm | 5 mm |
| Max. pulse energy (1 s) | 250 mJ | 750 mJ |
| Measurement time | 64–2048 ms | 64–2048 ms |
| Measurement rate | max. 15.6 Hz | max. 15.6 Hz |
| Size | 50 × 51.6 × 55 mm | 50 × 51 × 61.4 mm |
| Weight | 280 g | approx. 300 g |
| Best for | Tight integration spaces, edges and smaller radii | Fixed or robotic integration; rough or powdery surfaces |
OptiSense rates each sensor against substrate, coating and the condition the coating is in when measured. Some combinations need an application-specific calibration, which OptiSense provides.
| Substrate | Coating | Condition | Angle LLP1.6 | Angle LHP1.6 | Tube LLP3.5 | Tube LHP3.5 | Tube LHP10 | Cube-R | Cube-B |
|---|---|---|---|---|---|---|---|---|---|
| Metal | CDC | dry | ✓ | ✓ | ✓ | ✓ | |||
| Metal | Pigmented paint | wet / dry | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ |
| Metal | Clear coat | wet / powdered | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ |
| Metal | UV paint | wet / cured | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ |
| Metal | Zinc dust | dry | ✓ | ✓ | ✓ | ✓ | ✓ | ||
| Metal | Bonding agent | wet / cured | ✓ | ✓ | ✓ | ||||
| Metal | Powder coating | powdered | ✓ | ✓ | ✓ | ||||
| Metal | Adhesive | wet / dry | ✓ | ✓ | ✓ | ✓ | |||
| Metal | Rubber coating | dry | ✓ | ✓ | ✓ | ✓ | |||
| Rubber | Bonded coating | dry | ✓ | ✓ | ✓ | ||||
| Rubber | Adhesive | wet / cured | ✓ | ✓ | ✓ | ||||
| Ceramic | Pigmented paint | dry | ✓ | ✓ | ✓ | ✓ | |||
| Ceramic | Powder slurry | pre-dried | ✓ | ✓ | ✓ | ✓ | |||
| Ceramic | Conductive paste | pre-dried | ✓ | ✓ | ✓ | ✓ | ✓ | ||
| Glass | Pigmented paint | wet / dry | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ |
| Glass | Bonding agent | pre-dried | ✓ | ✓ | ✓ | ✓ | ✓ | ||
| Glass | Conductive paste | pre-dried | ✓ | ✓ | ✓ | ✓ | ✓ | ||
| Plastic | Bonding agent | wet / dry | ✓ | ✓ | ✓ | ||||
| Plastic | Laser paint | dry | ✓ | ✓ | ✓ | ✓ | ✓ | ||
| Plastic | Clear coat | wet / dry | ✓ | ✓ | ✓ | ✓ | |||
| Plastic | Powder coating | powdered | ✓ | ✓ | ✓ | ||||
| Plastic | Rubber coating | dry | ✓ | ✓ | ✓ | ✓ |
PaintChecker uses a photothermal method. A short, intense light pulse warms the coating surface by a few degrees, then the heat flows into the layers beneath. A thin coating cools faster than a thick one. An infrared detector records the temperature curve from a distance. The difference in thermal properties between coating and substrate then gives the absolute thickness.
OptiSense specifies the measurement procedure to DIN EN 15042-2. For a handheld check of the same coatings, see PaintChecker Mobile.
| Angle LLP1.6 | Angle LHP1.6 | Tube LLP3.5 | Tube LHP3.5 | Tube LHP10 | Cube-R | Cube-B | |
|---|---|---|---|---|---|---|---|
| Sensor | Laser, angle | Laser, angle | Laser, tube | Laser, tube | Laser, tube | LED, cube | LED, cube |
| Measurement range | 1–1000 µm | ||||||
| Measurement rate | max. 2.5 Hz | max. 15.6 Hz | |||||
| Measurement time | 125–1000 ms | 64–2048 ms | |||||
| Resolution | 1% of reading (typical) | ||||||
| Accuracy | 3% of reading (typical) | ||||||
| Measuring distance | 16 mm | 16 mm | 35 mm | 35 mm | 100 mm | 33 mm | 33 mm |
| Distance tolerance | ±1 mm | ±1 mm | ±2.5 mm | ±2.5 mm | ±5 mm | ±3 mm | ±3 mm |
| Angular tolerance | ±15° | ||||||
| Measuring field | 0.2 mm | 0.2 mm | 0.3 mm | 0.3 mm | 0.5 mm | 1 mm | 2 mm |
| Optical power | 650 mJ | 1250 mJ | 650 mJ | 1250 mJ | 1250 mJ | 1150 mJ | 250 mJ |
| Wavelength | 1470 nm | 1470 nm | 1470 nm | 1470 nm | 1470 nm | 980 nm | 365 nm |
| Laser class / risk group | 1M | 3R | 1M | 3R | 3R | Risk 1 | Risk 3 |
| Eye-safe | Yes | No | Yes | No | No | Yes | Yes |
| Size | 87 × 28 × 41 mm | 87 × 28 × 41 mm | Ø30 × 102 mm | Ø30 × 102 mm | Ø30 × 102 mm | 50 × 51.6 × 55 mm | 50 × 51.6 × 55 mm |
| Weight | 180 g | 180 g | 150 g | 150 g | 150 g | 280 g | 280 g |
| Protection | IP 50 | ||||||
Each sensor ships on its own, with the connecting cable as an accessory and a sensor holder available on request.
Yes. The measurement is contactless, so wet paint, powder before curing and pre-dried pastes are all read without touching them.
Up to eight. A PaintChecker Industrial Multi controller drives eight sensors of one series and records every point at the same time, so several parts or positions are measured without moving a sensor between them.
The standard-power laser sensors, Angle LLP1.6 and Tube LLP3.5, use OptiSense's LARES® technology and are eye-safe, as are both Cube LED sensors. The high-power laser sensors, Angle LHP1.6, Tube LHP3.5 and Tube LHP10, are laser class 3R and are not rated eye-safe.
Yes. The sensors weigh from 150 g to about 300 g and are built for robot mounting, with a sensor holder available on request. The Cube-B with 75 mm optics adds a wider distance and angle tolerance for robotic setups.
Some applications do. OptiSense creates application-specific calibrations as a service. Certified reference samples coated to a defined thickness are also available for checking the system in production.
Send us coated samples with the thickness range you need to control. We will test them and recommend the sensor and controller.
PaintChecker is made by OptiSense GmbH & Co. KG in Germany and supplied by Rhopoint Americas. Technical data come from the OptiSense PaintChecker Industrial Sensors datasheet (version 23.01) and the Cube-B 75 mm optics flyer (September 2026), as confirmed by OptiSense in October 2026. LARES is a registered trademark of OptiSense.
If the instrument is used in the wrong range, it can become oversaturated. This occurs when measurements on mirror-like surfaces (130+GU @60°) are taken using
The Challenge of High-Gloss, Dark and Premium Surfaces Highly polished, dark-toned, high-gloss finishes are particularly prone to exhibiting visible surface imperfections. These subtle visual anomalies
Automotive Interior Automotive Exterior Cartonboard Ceramics Concrete & Polished Concrete Furniture Geomembranes Metal Finishing Nonwoven material Packaging Paints & Coatings Paper & Printing Plastics Plastics
|
Uploaded
Failed
|
![]() |
Please note, this is NOT a quotation, just a confirmation of the price when purchased in the UK exclusive of VAT/duties